by

Download Winchiphead Port Devices Driver



The CH340 chip is used by a number of Arduino compatible boards to provide USB connectivity, you may need to install a driver, don’t panic, it’s easier than falling off a log, and much less painful.

  1. Download Winchiphead Port Devices Driver Printer
  2. Download Winchiphead Port Devices Driver
  3. Download Winchiphead Port Devices Driverpack
  4. Download Winchiphead Port Devices Driver Updater


Devices

Windows

(Manufacturer’s Chinese Info Link)

  1. Download the Windows CH340 Driver
  2. Unzip the file
  3. Run the installer which you unzipped
  4. In the Arduino IDE when the CH340 is connected you will see a COM Port in the Tools > Serial Port menu, the COM number for your device may vary depending on your system.

Older Windows Driver Version and Instructions

USB to Serial converter HL-340: download 32 and 64 bit windows drivers (PID/VID 4348:5523) Due to some reasons I had to run Windows XP on Virtualbox. After connected my classic pretty blue usb/serial cable converter, I found out that, as usual, Windows couldn’t recognize it. I wasted lot of time to find the appropriate working driver. Parallel port driver for Linux for WinChipHead ch341 chip - zoobab/ch341-parport. The Device Install Kit download site does not provide access to all Emerson Process Management device files. Device files distributed on DeltaV and AMS Device Manager release media are not duplicated for download from this site.

  1. Download the Windows CH340 Driver
  2. Unzip the folder.
  3. If you are running a 64Bit Windows: – run the SETUP_64.EXE installer.
  4. If you are running a 32Bit Windows: – run the SETUP_32.EXE installer.
  5. If you don’t know, try the 64 bit and if it doesn’t work, the 32 bit.
  6. In the Arduino IDE when the CH340 is connected you will see a COM Port in the Tools > Serial Port menu, the COM number for your device may vary depending on your system.

Macintosh

(Manufacturer’s Chinese Info Link) Sysview driver download for windows xp.

The following github has up to day pkg files for 1.3, 1.4 and 1.5 at time of writing, thanks to Joshua Wallis for bringing this to my attention…

Direct Download Links (from the github repo above):

  1. All equipment facilities installed on Dell OptiPlex 9010 are listed below. In order to facilitate the search for the necessary driver, choose one of the Search methods: either by Device Name (by clicking on a particular item, i.e. Intel(R) 7 Series/C216 Chipset Family Management Engine Interface - 1E3A) or by Device ID (i.e.
  2. Provide an INF file that specifies the Ports device setup class and the Serial function driver as the service for the port. To configure a serial port as COM port, comply with the requirements that are defined in Configuration of COM Ports.

See the github link above for installation instructions if you need them.

Download Winchiphead Port Devices Driver Printer

Previous macinstosh downloads if the above doesn’t work for you…

(V1.3) Download the CH340 Macintosh Signed Driver for Mavericks (10.9), Yosemite (10.10) and El Capitan (10.11) and Sierra (10.12)

Inside the zip file you will find a PDF and a “pkg” file, short version, double click the pkg file, the PDF has some extra information.

OSX Sierra (10.12) Note

Smsc scsi & raid devices driver win 7. A kindly user, Maarten Segers reports

FYI, the driver documented here WILL crash on OSX Sierra.

Make sure to use this one instead: https://github.com/MPParsley/ch340g-ch34g-ch34x-mac-os-x-driver

I can personally not test on MacOS and can not vouch for the above drivers at github, but there you go.

Download Winchiphead Port Devices Driver

See uninstalling information at the bottom of the page if the driver causes problems for you.

Here is an older version of the Mac driver, NOT FOR 10.12 Sierra

(V1.0) Download the CH340 Macintosh Signed Driver for Mavericks (10.9), Yosemite (10.10) and El Capitan (10.11)

Linux

Download Winchiphead Port Devices Driverpack

(Manufacturer’s Chinese Info Link)

Download Winchiphead Port Devices Driver Updater

Drivers are almost certainly built into your Linux kernel already and it will probably just work as soon as you plug it in. If not you can download the Linux CH340 Driver (but I’d recommend just upgrading your Linux install so that you get the “built in” one).

Uninstalling From Macinstosh

A couple of Mac users have said “the driver crashes my mac Sierra how do I uninstall”.

Download tallygenicom driver download. Firstly regards the crash make sure you installed the 1.3 version of the driver, not the old one. You could download it directly from the Manufacturers Website in case they have issued an update since I wrote this page.

Secondly a quick google search reveals that this is how you uninstall:

  1. Open a terminal and type: cd /Library/Extensions/
  2. Verify that the .kext file is present: ls | grep usbserial.kext
  3. Output should be: usbserial.kext
  4. Then type: sudo rm -R usbserial.kext
  5. Verify that the .kext file has been removed: ls | grep usbserial.kext
  6. Output should be empty.
  7. After you should remove the files stored in receipts folder: cd /private/var/db/receipts/
  8. Find the enties: ls | grep usbserial*
  9. Output should be: codebender.cc.ch34xinstaller.usbserial.pkg.bom codebender.cc.ch34xinstaller.usbserial.pkg.plist
  10. Remove each one of the files of the above list: sudo rm -r filename`